Bathroom renovations
Bathroom Remodel…part eight; Final pics
Tuesday, October 14th, 2008Finally Finished!
What made this project so difficult and enjoyable all at the same time is that all the woodwork is applied over the existing tile. The design plan was to tone down the existing tile work and at the same time give the room more traditional woodwork and more function with minimum disruption to the owners home. The only tear out was the old vanity and the the two entry doors.
The challenge… A ll the pieces were designed, finished in my shop and field installed with the minimum of anchors and nails to fill. No on site cutting except some fitting cuts that I did outside. Did I mention earlier, the room; I mean every corner and surface was 3/8″ in 48″ out. It was almost like the masons and framers guessed at plum and level. One thing I can say for sure is that it was consistently off. How the tile man did his job I will never know; but it looked good enough not to have to tear it all out.
The owners were so pleased with the final results that they actually took the time to send me a real thank you note! That make it worth all the effort. What do you think… problem solved?
Thank you from MCKen…
Bathroom Remodel part seven…
Thursday, June 26th, 2008
All in the details…
Working over the existing tile has been a challenge. All the details that have been designed in wood have to be finished off site in my shop. That means every part has to fit or to be adjustable on site by sanding to fit only. No caulking here!
After installing the basics, the two entrance doors into this space that were flat panel painted just didn’t look good up against the new woodwork. I am now working on two, four raised panel, cathedral head maple doors to match all the other woodwork to replace the painted existing doors. One of them has a special venting detail in the kick rail.
More to come…
Bathroom Part Six…Woodworking Details
Monday, June 2nd, 2008
The most eye catching details found in a small space is going to be at eye level. What better place to create the most impressive woodworking detail is above the toilet and vanity. A closed cabinet and a tri-mirror, complete with reed pilasters and rosettes are in order. Maybe even add some figured maple plaques and a raised carving center piece. To complete the tile cover up, how about a raised panel bulkhead.
Bathroom Part Five…Starting to install the new wood work.
Thursday, May 8th, 2008
The new vanity fit nicely into the corner but the challenge is when the plumbing has to be let into the frame of the vanity box in a limited space. The drain runs to the right side crossing over one of the drawers. This is one of those times that it was more important to move the drain pipe than it was to chop the drawer box to clear. Custom design can’t cover all the unexpected conditions, especially when the measuring of the new was done before the tear out. The supply lines were in the center back and cleared the drawer below the shut offs. A nice feature of space design is to not give the plumbing any more room than it needs. The doors are snap release and are always removed until the plumbing is completed.
I made the top out of solid surface, mfgr by “Hannex”. The piece comes to me 30″ x 120″ x 1/2″ thick and must be fabricated into the configuration of the order. The bowl is glued on and becomes seamless. The back splashes were made of the same material along with the shaving shelf that ran all across the vanity and toilet.
The bulkhead panels and the crowns were also installed. Overall, this was a good day!
Master Bath Remodeling and Makeover Project - Part Three, The Tear Out.
Tuesday, April 22nd, 2008Part Three…The tear Out.
The tear out can be a very simple process and of course it can be your worst nightmare. I had decided early on that I would build the new vanity and it’s counter top before tear out. The idea is to leave the space in a working condition until some of the woodwork was ready to go back. In custom fabrication, it’s what you don’t see that can get you in trouble. 
The Luck was with me. The only surprise was a little water damage behind the unit that since had dried. The moisture had produced some mold. There was also some evidence of termite damage but not active.
I cut the wallboard out from behind the old vanity, removed some foam insulation and a couple of furring strips. The block wall behind was clean and in good shape.
The pipes and valves were new but the evidence of the old abandoned pipes were still there. Generally if they are not in the way, I just make sure they are sealed and intact and just cover them back.
The old recessed lites and the mirrored medicine cabinet came out without a hitch.
Now it’s time to clean up and start installing the new wood work.
Master Bath Remodeling and Makeover Project - Part Two
Tuesday, April 22nd, 2008Part Two…Plan and S
ketch some Proposals.
Money is always a concern. My challenge is to make suggestions that make the space better but always keep the budget in mind. In this case, we didn’t have a budget but rather needed to solve the problems first and then put a price tag on the project later. Risky because if at the end of the planning stage, I solve all the issues but let the expense get more than the owner wants to spend, a lot of time gets wasted and I don’t get paid for time invested.
Two sketches later and lot of discussion, here is the list of proposed changes.
1-Make the vanity taller and deeper. ( more to kitchen counter standards ).
2-Improve drawer size and number. 4 drawers in the old to 7 in the same space. Also use soft close and full extension slides.
3-All maple, raised panel construction (euro style), w/ a soft brown stain and burnt umber glazed finish.
4-Razor shelf over the vanity and continue over the toilet.
5-Solid surface vanity counter w/ seamless sink and matching back splash.
6-Cabinets over the toilet and wood framed medicine cabinet over the vanity. A good place to add carvings, rope moldings, and in short, much needed traditional details.
7-Crown details all around the room.
8-Cover the existing bulkhead w/ raised panel matching woodwork.
Master Bath Remodeling and Makeover Project
Sunday, April 20th, 2008Part One… Introduction to the project.
Bathrooms normally are tight spaces that have to perform a lot of 
functions. Good maintenance and most bath spaces work good for years. However, some baths, like this one, are already in good working order. The room looks good and really don’t need anything except a little makeover. The process starts with visiting with the owners and creating a list of what they would like changed in the space. Usually this consists of color and material changes.
This bath has a lot of nice tile work. The floors, three walls, the fully enclosed shower, and a bulkhead are completely covered with tile. We all agreed that it was OK not to tear it all out, if I could figure out a way to tone it down. The existing vanity was the old standard of 30″ high and needed to be raised to a more comfortable 36″ high. Storage in the large mirrored medicine cabinet needed upgrading along with improving the drawer configuration of the vanity. More traditional wood work was also on the list of must haves.
The next step is for me to take the owners concerns and draw some proposed concept sketches.